Effect of Macro and Micro Polypropylene Fibers on the Flexural Behavior of RC Slabs

Miaad S. Fariq; Feirusha S.M. Kakshar

doi:10.21271/ZJPAS.37.6.8

Authors

Miaad S. Fariq Department of Civil Engineering, College of Engineering, Salahaddin University- Erbil, Erbil, Kurdistan-Iraq
Feirusha S.M. Kakshar Department of Civil Engineering, College of Engineering, Salahaddin University- Erbil, Erbil, Kurdistan-Iraq

DOI:

https://doi.org/10.21271/ZJPAS.37.6.8

Keywords:

Polypropylene fiber, Flexural strength, One-way slab, Hybrid fiber reinforced concrete

Abstract

This research highlights the effect of the micro polypropylene fibers (mPPF), macro polypropylene fibers (MPPF), and hybrid fibers (combination of mPPF and macro steel fiber at the rate of half) on the flexural strength of the one-way reinforced concrete (RC) slabs. The optimum fiber content is considered based on the ultimate flexural load and mechanical properties. A total of 10 simply supported one-way RC slabs in dimensions 1100 × 400 × 80 mm (length × width × thickness) were prepared and tested under a four-point bending test to investigate their response to first crack load, ultimate load, deflection, and strain. The dosage of the fibers was 0.5%, 1%, and 1.5% by total volume of concrete. Also, the aspect ratios were 375 for mPPFs, 50 for MPPFs, 35 for macro steel fibers. The test results revealed that the flexural stiffness and crack resistance of the one-way RC slabs were improved compared to the control slab. Though the ultimate flexural load increased by 29.73% for the slab with mPPF at 0.5% dosage, 32.46% for the slab with MPPF at 0.5% dosage. The slab with steel fiber + mPPF at 1.5% dosage demonstrated an increased ultimate flexural load of 28.2% compared to the control slab, while the cracks widened. The load-deflection curve of the slab with mPPF at 0.5% dosage displayed the most elastic one-way RC slab among all the slabs, as it enhanced the first crack load by 112%. The load-deflection curve of MPPFRC slabs and the slabs with hybrid fibers displayed the gradual decline in post-cracking behavior.

References

Abbas, A.M., Hussain, H.K., Ojaimi, M.F., 2022. Shear and Flexural Behavior of Flat Slabs Casted with Polyolefin Fiber-Reinforced Concrete. Fibers 10, 34. https://doi.org/10.3390/fib10040034

ACI 544.4R-18, 2018. Guide to design with fiber-reinforced concrete. American Concrete Institute.

Al-Rousan, R., Alnemrawi, B.R., 2024. NLFEA of the behavior of polypropylene-fiber-reinforced concrete slabs with square opening. Buildings 14, 480.

Al-Rousan, R.Z., 2022. Influence of macro synthetic fibers on the flexural behavior of reinforced concrete slabs with opening. Civ Eng J 8, 2001–2021.

ASTM C39/C39M-21, 2023. Test Method for Compressive Strength of Cylindrical Concrete Specimens. https://doi.org/10.1520/C0039_C0039M-21

ASTM C496/C496M-17, 2017. Test Method for Splitting Tensile Strength of Cylindrical Concrete Specimens. https://doi.org/10.1520/C0496_C0496M-17

Banthia, N., Dubey, A., 2000. Measurement of Flexural Toughness of Fiber-Reinforced Concrete Using a Novel Technique—Part 2: Performance of Various Composites. MJ 97. https://doi.org/10.14359/799

Başsürücü, M., Fenerli̇, C., Kina, C., Akbaş, Ş.D., 2022. Effect of Fiber Type, Shape and Volume Fraction on Mechanical and Flexural Properties of Concrete. Journal of Sustainable Construction Materials and Technologies 7, 158–171. https://doi.org/10.47481/jscmt.1137088

Blazy, J., Blazy, R., 2021. Polypropylene fiber reinforced concrete and its application in creating architectural forms of public spaces. Case Studies in Construction Materials 14, e00549. https://doi.org/10.1016/j.cscm.2021.e00549

Dhanapal, J., Jeyaprakash, S., 2020. Mechanical properties of mixed steel fiber reinforced concrete with the combination of micro and macro steel fibers. Structural Concrete 21, 458–467. https://doi.org/10.1002/suco.201700219

Facconi, L., Plizzari, G., Minelli, F., 2019. Elevated slabs made of hybrid reinforced concrete: Proposal of a new design approach in flexure. Structural Concrete 20, 52–67. https://doi.org/10.1002/suco.201700278

Fall, D., 2014. Steel Fibres in Reinforced Concrete Structures of Complex Shapes (PhD Thesis). CHALMERS UNIVERSITY OF TECHNOLOGY, Gothenburg, Sweden.

Hasan, A., Maroof, N., Ibrahim, Y., 2019. Effects of Polypropylene Fiber Content on Strength and Workability Properties of Concrete. Polytechnic j. 9, 7–12. https://doi.org/10.25156/ptj.v9n1y2019.pp7-12

Khan, Q.U.Z., Ahmad, A., Raza, A., Labibzadeh, M., Iqbal, M., 2021. Structural Performance of One-Way Slabs Reinforced with Steel and Polypropylene Fibers. jkukm 33, 193–203. https://doi.org/10.17576/jkukm-2021-33(2)-04

Mashrei, M.A., Sultan, A.A., Mahdi, A.M., 2018. Effects of polypropylene fibers on compressive and flexural strength of concrete material. IJCIET 9, 2208–2217.

Ndububa, E., 2022. Concrete from Alternative and Waste Materials, in: Saleh, H.M., Mhadhbi, M., Hassan, A.I. (Eds.), Reinforced Concrete Structures - Innovations in Materials, Design and Analysis. IntechOpen. https://doi.org/10.5772/intechopen.1000571

Newman, J.B., Choo, B.S., 2003. Advanced concrete technology. Butterworth-Heinemann, Oxford.

Omer, M.I., Jaf, D.K., 2020. Evaluation of Full-Scale Concrete Frames Exposed to Natural Fires at Early Ages. ZJPAS 32, 115–128. https://doi.org/10.21271/ZJPAS.32.2.12

Pangestuti, E.K., Handayani, S., Adila, H., Primerio, P., 2021. The effect of polypropylene fiber addition to mechanical properties of concrete. IOP Conf. Ser.: Earth Environ. Sci. 700, 012057. https://doi.org/10.1088/1755-1315/700/1/012057

Qader, Z.M., Kakshar, F.S.M., 2023. Experimental Investigation on Bond Stress Behavior of Sand-Coated GFRP Bars with Concrete. ZJPAS 35, 30–38. https://doi.org/10.21271/ZJPAS.35.3.3

Rahmdel, J.M., Shafei, E., Salamat Ravandi, K., Zirakian, T., 2025. Experiments on Strength and Ductility Characteristics of Polypropylene Fiber-Reinforced Concrete. J. Civ. Eng. Constr. 14, 20–27. https://doi.org/10.32732/jcec.2025.14.1.20

Ramadevi, K., Babu, D.L.V., 2012. Behaviour of hybrid fiber reinforced concrete slabs in frames under static loading. Eco. Env. & Cons. 18, 975–979.

Ramujee, K., 2013. Strength properties of polypropylene fiber reinforced concrete. International journal of innovative research in science, engineering and technology 2, 3409–3413.

Richardson, A.E., 2006. Compressive strength of concrete with polypropylene fibre additions. Structural Survey 24, 138–153. https://doi.org/10.1108/02630800610666673

Sadiqul Islam, G.M., Gupta, S.D., 2016. Evaluating plastic shrinkage and permeability of polypropylene fiber reinforced concrete. International Journal of Sustainable Built Environment 5, 345–354. https://doi.org/10.1016/j.ijsbe.2016.05.007

Shatnawi, A., Abdel-Jaber, M., Bsisu, K.A.-D., 2016. Experimental Investigation of One-Way Shear Behavior in Reinforced Concrete Flat Slabs Strengthened with Micro-Polypropylene Fibers. Presented at the 2016 4th International Conference on Sensors, Mechatronics and Automation (ICSMA 2016). https://doi.org/10.2991/icsma-16.2016.48

Wang, J., Dai, Q., Si, R., Guo, S., 2019. Mechanical, durability, and microstructural properties of macro synthetic polypropylene (PP) fiber-reinforced rubber concrete. Journal of Cleaner Production 234, 1351–1364. https://doi.org/10.1016/j.jclepro.2019.06.272

Yaseen, S.A., 2020. Flexural Behavior of Self Compacting Concrete T-Beams Reinforced with AFRP. ZANCO Journal of Pure and Applied Sciences 32, 107–114.

Zainal, S.M.I.S., Hejazi, F., Mafaileh, A.M.A., 2023. Strengthening of Reinforced Concrete slabs using macro and micro synthetic fibers. Structures 51, 1579–1590. https://doi.org/10.1016/j.istruc.2023.03.120

Zheng, Z., Feldman, D., 1995. Synthetic fibre-reinforced concrete. Progress in Polymer Science 20, 185–210. https://doi.org/10.1016/0079-6700(94)00030-6