Fabrication of High-Density Polyethylene Matrix Surface Composite Reinforced by Various Powder Materials through Friction Stir Processing

Abdulbasit Abdulqadir Hamza; Shawnam Rashied Jalal

doi:10.21271/ZJPAS.37.4.10

Authors

Abdulbasit Abdulqadir Hamza Department of Mechanical and Mechatronics, College of Engineering, Salahaddin University-Erbil, Erbil, Kurdistan Region, Iraq
Shawnam Rashied Jalal Department of Mechanical and Mechatronics, College of Engineering, Salahaddin University-Erbil, Erbil, Kurdistan Region, Iraq

DOI:

https://doi.org/10.21271/ZJPAS.37.4.10

Keywords:

Friction Stir Processing, High-density polyethylene Surface Composites, Mechanical Properties, Reinforcement Powders

Abstract

Friction Stir Processing (FSP) is a promising technique to improve the surface properties of materials. Compared to metals, the FSP of polymeric materials was less studied. Therefore, in the present work, high-density polyethylene (HDPE) surface composite was fabricated by the addition of reinforcements such as Graphene (C), Silicon carbide (SiC), Silicon dioxide (SiO₂), and Copper (Cu) powders. The effect of FSP parameters such as tool rotational speed (478, 679, and 925) rpm, traverse speed (22, 37, and 51) mm/min, and amount of added particles (10, 15, and 20) % on the mechanical properties of the fabricated samples were studied. The results showed that as the reinforcement powders were added to the matrix material, led to enhancements in each of the tensile strength, microhardness, and impact strength. At the optimum set of process parameters, the graphene-reinforced composites have better improvement in terms of tensile and impact strength where increased by (47.2 and 55.6) % respectively. On the other hand, in terms of microhardness, the SiC-reinforced composite exhibited greater augmentation, registering 20.16 %. While, the elongation of all fabricated composites decreased in comparison to the parent material. Based on the table of analysis of variance (ANOVA), it is noticed that the tool rotational speed has the largest effect on the quality of the products among the other parameters, followed by tool traverse speed and the amount of particles has the least contribution and effect. Considering the information provided, the friction stir process method can be used to repair cracks and other defects in polymeric materials.

References

ABDEL-GWAD, E., OMAR, A.-B. & RADWAN, A. 2015. Loadability of friction stir welded joints of high density polyethylene. Port-Said Engineering Research Journal, 19, 100-107.

AHMADI, H., MOSTAFA ARAB, N. & GHASEMI, F. A. 2014. Optimization of process parameters for friction stir lap welding of carbon fibre reinforced thermoplastic composites by Taguchi method. Journal of Mechanical Science and Technology, 28, 279-284.

ASTM, A. 2015. Standard Test Method for Rubber Property-Durometer Hardness ASTM: West Conshohocken, PA, USA, D224015:2015.

AZARSA, E. & MOSTAFAPOUR, A. 2013. On the feasibility of producing polymer–metal composites via novel variant of friction stir processing. Journal of Manufacturing Processes, 15, 682-688.

AZHIRI, R. B., TEKIYEH, R. M., ZEYNALI, E., AHMADNIA, M. & JAVIDPOUR, F. 2018. Measurement and evaluation of joint properties in friction stir welding of ABS sheets reinforced by nanosilica addition. Measurement, 127, 198-204.

BARMOUZ, M., SEYFI, J., GIVI, M. K. B., HEJAZI, I. & DAVACHI, S. M. 2011. A novel approach for producing polymer nanocomposites by in-situ dispersion of clay particles via friction stir processing. Materials Science and Engineering: A, 528, 3003-3006.

BATTISTI, M. G. & FRIESENBICHLER, W. 2013. Injection-moulding compounding of PP polymer nanocomposites. Strojniški vestnik-Journal of Mechanical Engineering, 59, 662-668.

BOZKURT, Y. 2012. The optimization of friction stir welding process parameters to achieve maximum tensile strength in polyethylene sheets. Materials & Design, 35, 440-445.

BUTOLA, R., PANDIT, D., PRATAP, C. & CHANDRA, P. 2022. Two decades of friction stir processing–a review of advancements in composite fabrication. Journal of Adhesion Science and Technology, 36, 795-832.

DERAZKOLA, H. A. & SIMCHI, A. 2018. Effects of alumina nanoparticles on the microstructure, strength and wear resistance of poly (methyl methacrylate)-based nanocomposites prepared by friction stir processing. Journal of the mechanical behavior of biomedical materials, 79, 246-253.

EŞME, U. 2009. APPLICATION OF TAGUCHI METHOD FOR THE OPTIMIZATION OF RESISTANCE SPOT WELDING PROCESS. Arabian Journal for Science & Engineering (Springer Science & Business Media BV), 34.

FARSHBAF ZINATI, R. 2015. Experimental evaluation of ultrasonic-assisted friction stir process effect on in situ dispersion of multi-walled carbon nanotubes throughout polyamide 6. The International Journal of Advanced Manufacturing Technology, 81, 2087-2098.

GAO, J., LI, C., SHILPAKAR, U. & SHEN, Y. 2015. Improvements of mechanical properties in dissimilar joints of HDPE and ABS via carbon nanotubes during friction stir welding process. Materials & Design, 86, 289-296.

HAJIDEH, M. R., FARAHANI, M. & RAMEZANI, N. M. 2018. Reinforced dissimilar friction stir weld of polypropylene to acrylonitrile butadiene styrene with copper nanopowder. Journal of Manufacturing Processes, 32, 445-454.

HAMZA, A. A. & JALAL, S. R. 2022. A review on manufacturing the polymer composites by friction stir processing. European Polymer Journal, 178, 111495.

HOSEINLAGHAB, S., MIRJAVADI, S. S., SADEGHIAN, N., JALILI, I., AZARBARMAS, M. & GIVI, M. K. B. 2015. Influences of welding parameters on the quality and creep properties of friction stir welded polyethylene plates. Materials & Design, 67, 369-378.

IFTIKHAR, S. H., MOURAD, A.-H. I., SHEIKH-AHMAD, J., ALMASKARI, F. & VINCENT, S. 2021. A comprehensive review on optimal welding conditions for friction stir welding of thermoplastic polymers and their composites. Polymers, 13, 1208.

ISO, B. 2012. Plastics–determination of tensile properties. British Standard, Germany, ISO 527-2:2012(E).

ISO, B. 2019. Plastics–determination of tensile properties. British Standard, Germany, ISO 527-1:2019(E).

ISO, B. E. 2010. Plastics–determination of Charpy imact properties. British Standard, Germany, ISO 179-1:2010.

KAKA, D. O. 2022. Investigation of the mechanical properties for polymer reinforced by nanoparticles with considering viscoelasticity of the matrix. Zanco Journal of Pure and Applied Sciences, 34, 92-101.

KARIMI, S., ARAB, S. M., ZEIDABADI, S. R. H. & JAVADPOUR, S. 2021. Tribological behavior and mechanical properties of friction stir processed HDPE/Fe-Fe3O4 composites. Synthesis and Sintering, 1, 176-182.

KHAN, I., HUSSAIN, G., A AL-GHAMDI, K. & UMER, R. 2019. Investigation of impact strength and hardness of UHMW polyethylene composites reinforced with nano-hydroxyapatite particles fabricated by friction stir processing. Polymers, 11, 1041.

KHAN, I., HUSSAIN, G., TARIQ, M. & ILYAS, M. 2018. Fabrication of UHMW polyethylene/nano-hydroxyapatite biocomposite via heat-assisted friction stir processing. The International Journal of Advanced Manufacturing Technology, 96, 3651-3663.

KUMAR, A., AERON, S., PANT, M., KRISHAN, H., ZAPHAR, S., MITTAL, A. & KUMAR, N. 2025. Enhanced Electrical Conductivity of Graphite through Band Gap Reduction by Ferrite Nanoparticles. Zanco Journal of Pure and Applied Sciences, 37, 40-52.

MADHU, G., BHUNIA, H., BAJPAI, P. K. & CHAUDHARY, V. 2014. Mechanical and morphological properties of high density polyethylene and polylactide blends. Journal of Polymer Engineering, 34, 813-821.

MOFAKHAMI, E., GERVAT, L., FAYOLLE, B., MIQUELARD-GARNIER, G., OVALLE, C. & LAIARINANDRASANA, L. 2024. Effect of fibre concentration on the mechanical properties of welded reinforced polypropylene. Composites Part B: Engineering, 269, 111111.

MUHAMMAD, F. & JALAL, S. 2022. An overview of the effect of stirrer design on the mechanical properties of Aluminium Alloy Matrix Composites fabricated by stir casting. Zanco Journal of Pure and Applied Sciences, 34, 18-35.

OLEIWI, J. K., SALIH, S. I. & ABD ALKHIDHIR, S. 2018. Study Some Mechanical Properties of Binary Polymer Blends Fabricated by Friction Stir Processing. Journal of University of Babylon for Engineering Sciences, 26, 362-370.

RAZA, K., SHAMIR, M., QURESHI, M. K. A., SHAIKH, A. S. & ZAIN-UL-ABDEIN, M. 2018. On the friction stir welding, tool design optimization, and strain rate-dependent mechanical properties of HDPE–ceramic composite joints. Journal of Thermoplastic Composite Materials, 31, 291-310.

ROSTAMIYAN, Y. & ZAFERANI, M. 2019. Fabrication of polyethylene-based surface composite reinforced by carbon nano-tube and nano-clay through friction stir processing. Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications, 233, 580-587.

RUDRAPATI, R. 2022. Effects of welding process conditions on friction stir welding of polymer composites: A review. Composites Part C: Open Access, 8, 100269.

SALIH, S. I., OLEIWI, J. K. & ABD ALKHIDHIR, S. 2018. Comparative study of some mechanical properties of hybrid polymeric composites prepared by using friction stir processing. Journal of Advanced Research in Dynamic and Control Systems, 10, 1316-1326.

SAURABH, A., JOSHI, K., MANOJ, A. & VERMA, P. C. 2022. Process optimization of automotive brake material in dry sliding using taguchi and ANOVA techniques for wear control. Lubricants, 10, 161.

SHARMA, V. & TRIPATHI, P. K. 2022. Approaches to measure volume fraction of surface composites fabricated by friction stir processing: a review. Measurement, 193, 110941.

YUAN, S., LI, S., ZHU, J. & TANG, Y. 2021. Additive manufacturing of polymeric composites from material processing to structural design. Composites Part B: Engineering, 219, 108903.

ZEBARJAD, S. 2007. Production of polyethylene/carbon nanotube nanocomposite using mechanical milling process and investigation of its microstructure Abstract No: 107.

ZHITOMIRSKY, V., GRIMBERG, I., JOSEPH, M., BOXMAN, R., MATTHEWS, A. & WEISS, B. 1999. Vacuum arc deposition of conductive wear resistant coatings on polymer substrates. Surface and Coatings Technology, 120, 373-377.